Stellinox Stainless Pvt. Ltd. manufactures high-quality Re-Rolled Coil without the use of heat. The stainless steel coil undergoes state-of-the-art technology that applies mechanical stress, achieving precision and uniform gauge reduction.

CONTACT US →
GRADES / MATERIAL DESIGNATION:
Size Range in MM

THICKNESS :

0.080MM TO 0.80MM

WIDTH :

3MM To 605MM

Surface Finish

BA

HARD

(¼ Hard, ½ Hard, ¾ Hard, Full Hard)

Edge Condition

MILL EDGE

DEBURRED

SLIT EDGE

ROUND

Grade Relevant Standard Nomenclature C% Mn% P% S% Si% Cr% Ni% Mo% N2% Cu% Other Elements Hard in VPN TS in MPa YS in MPa % El
LOW Ni AUSTENITIC STEEL
200-Series
SEM 202 JSL STD JSLAUS/J-1 0.080 6.00-8.00 0.07 0.01 0.75 16.00-18.00 4.00-6.00 - 0.10 1.50-2.00 - 222 Max 550 Min 205 Min 40 Min
ASTM240 202 0.080 3.00-5.00 0.045 0.03 1.00 17.00-18.00 4.00-6.00 - 0.05-0.20 2.00-3.00 - 201 Max 515 Min 205 Min 40 Min
EN-10088 X12CrMnNiN18-9-5/1.4373 0.150 7.50-10.50 0.045 0.015 1.00 17.00-19.00 4.00-6.00 - 0.05-0.20 *** - 241 Max 680-880 340 Min 45 Min
SS 201 JSL STD. JSLAUS/J-1 0.080 6.00-8.00 0.07 0.01 0.75 16.00-18.00 4.00-6.00 - 0.10 1.50-2.00 - 222 Max 550 Min 205 Min 40 Min
ASTM240 201 0.150 5.50-7.50 0.06 0.01 0.75 16.00-18.00 3.50-5.50 - 0.25 0.0 - 223 Max 515 Min 260 Min 40 Min
EN-10088 X12CrMnNiN17-7-5/1.4372 0.150 5.50-7.50 0.045 0.03 1.00 16.00-18.00 3.50-5.50 - 0.02-0.25 *** - 241 Max 750-950 350 Min 45 Min
204 Cu/N2 IS-15997 N2 0.1 6.50-9.0 0 0.060 0.010 0.75 16.00-17.50 1.50-3.50 - 0.10-0.20 2.00-4.00 - *** 620 Min 310 Min 40 Min
JSL AUS JSL STD. JSLAUS/J-1 0.080 6.00-8.00 0.07 0.01 0.75 16.00-18.00 4.00-6.00 - 0.10 1.50-2.00 - 222 Max 550 Min 205 Min 40 Min
J-4 JSL STD. J-4 0.100 8.50-10.00 0.08 0.01 0.75 15.00-16.00 1.00-2.00 - 0.20 1.50-2.00 - 243 Max 650 Min 325 Min 40 Min
JSL-USD JSL STD. JSL-USD 0.150 9.75-10.75 0.1 0.015 0.75 14.50-16.00 0.40-0.55 - 0.20 1.00-1.30 - 220-280 700 350 Min 40 Min
JSL-UDD JSL STD JSL-UDD 0.150 9.75-10.75 0.1 0.015 0.75 14.75-16.25 0.50-0.60 - 0.20 1.90-2.20 - 220-280 700 Min 350 Min 40 Min
AUSTENITIC STEEL
300-Series
SS 301 ASTM240 301 0.150 2.00 0.045 0.03 1.00 16.00-18.00 6.00-8.00 - 0.10 - - 217 Max 515 Min 205 Min 40 Min
EN-10088 X10CrNi18-8/1.4310 0.05-0.15 2.00 0.045 0.015 1.00 16.00-19.00 6.00-9.50 - 0.11 ** *** *** 600-950 250 Min 40 Min
IS-6911 301 0.150 2.00 0.045 0.03 1.00 16.00-18.00 6.00-8.00 - *** - - 218 Max 590 Min 220 Min 40 Min
JIS-4305 SUS-301 0.150 2.00 0.045 0.03 1.00 16.00-18.00 6.00-8.00 - *** - - 218 Max 520 Min 205 Min 40 Min
SS 304 ASTM240 304 0.080 2.00 0.045 0.03 1.00 18.00-20.00 8.00-10.50 - 0.10 - - 201 Max 515 Min 205 Min 40 Min
EN-10088 X5CrNi18-10/1.4301 0.070 2.00 0.045 0.015 1.00 17.50-19.50 8.00-10.50 - 0.10 - - 201 Max 540-750 230 Min 45 Min
IS-6911 304 0.080 2.00 0.045 0.03 1.00 17.50-20.00 8.00-10.50 - *** - - 198 Max 400 Min 200 Min 40 Min
JIS-4305 SUS 304 0.080 2.00 0.045 0.03 1.00 18.00-20.00 8.00-10.50 - *** - - 200 Max 520 Min 205 Min 40 Min
SS 304-L ASTM240 304-L 0.030 2.00 0.045 0.03 1.00 18.00-20.00 8.00-12.00 - 0.10 - - 201 Max 485 Min 170 Min 40 Min
EN-10088 X2CrNi19-9/1.4307 0.030 2.00 0.045 0.015 1.00 17.50-19.50 8.00-10.50 - *** - - *** 520-700 220 Min 45 Min
IS-6911 304-L 0.030 2.00 0.045 0.03 1.00 18.00-20.00 8.00-12.00 - *** - - 198 Max 400 Min 180 Min 40 Min
JIS-4305 SUS-304-L 0.030 2.00 0.045 0.03 1.00 18.00-20.00 9.00-13.00 - *** - - 200 Max 480 Min 175 Min 40 Min
SS 316 ASTM240 316 0.080 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 0.10 - - 217 Max 515 Min 205 Min 40 Min
EN-10088 X5CrNiMo17-12-2/1.4401 0.070 2.00 0.045 0.015 1.00 16.50-18.50 10.00-13.00 2.00-2.50 0.10 - - *** 530-680 240 Min 40 Min
IS-6911 316 0.080 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 *** - - 198 Max 490 Min 210 Min 40 Min
JIS-4305 SUS 316 0.080 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 *** - - 200 Max 520 Min 205 Min 40 Min
SS 316-L ASTM240 316-L 0.030 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 0.10 - - 217 Max 485 Min 170 Min 40 Min
EN-10088 X2CrNiMo17-12-2/1.4404 0.030 2.00 0.045 0.015 1.00 16.50-18.50 10.00-13.00 2.00-2.50 0.10 - - *** 530-680 240 Min 40 Min
IS-6911 316-L 0.030 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 *** - - 198 Max 440 Min 210 Min 40 Min
JIS-4305 SUS 316-L 0.030 2.00 0.045 0.03 1.00 16.00-18.00 10.00-14.00 2.00-3.00 *** - - 200 Max 480 Min 175 Min 40 Min
SS 321 ASTM240 321 0.080 2.00 0.045 0.03 1.00 17.00-19.00 9.00-12.00 - 0.10 - Ti 5X(C+N)min, 0.70 max 217 Max 515 Min 205 Min 40 Min
EN-10088 X6CrNiTi18-10/1.4541 0.080 2.00 0.045 0.015 1.00 17.50-19.50 9.00-12.00 * - - Ti 5X(C+N)min, 0.70 max *** 520-720 220 Min 40 Min
IS-6911 321 0.080 2.00 0.045 0.03 1.00 17.00-19.00 9.00-12.00 - *** - Ti 5X(C+N)min, 0.80 max 198 Max 490 Min 210 Min 35 Min
JIS-4305 SUS 321 0.080 2.00 0.045 0.03 1.00 17.00-19.00 9.00-13.00 - *** - Ti 5X(C+N)min 200 Max 520 Min 205 Min 40 Min
FERRITIC STEEL
400-Series
SS 409 ASTM240 S40910 0.030 1.00 0.04 0.02 1.00 10.50-11.70 0.5 - 0.03 - Ti 6X(C+N)min, 0.50 max 179 Max 380 Min 170 Min 20 Min
EN-10088 X6CrTi12/1.4512 0.030 1.00 0.04 0.015 1.00 10.50-12.50 — - - - Ti 6X(C+N)min, 0.65 max 180 Max 380-560 210 Min 25 Min
IS-6911 409 0.030 1.00 0.04 0.02 1.00 10.50-11.70 0.5 - 0.03 - Ti 6X(C+N)min, 0.50 max 183 Max 380 Min 170 Min 20 Min
SS 410-S ASTM240 410-S 0.080 1.00 0.04 0.03 1.00 11.50-13.50 0.6 - - - - 183 Max 415 Min 205 Min 22 Min
EN-10088 X6Cr13/1.4000 0.080 1.00 0.04 0.015 1.00 12.00-14.00 *** - - - - 183 Max 400-600 250 Min 19 Min
IS-6911 410S 0.080 1.00 0.04 0.03 1.00 11.50-13.50 0.6 - - - - 183 Max 415 Min 205 Min 22 Min
SS 430 ASTM240 430 0.120 1.00 0.04 0.03 1.00 16.00-18.00 0.75 - - - - 183 Max 450 Min 205 Min 22 Min
EN-10088 X6Cr17/1.4016 0.120 1.00 0.04 0.015 1.00 16.00-18.00 *** - - - - *** 450-600 260 Min 20 Min
IS-6911 430 0.120 1.00 0.04 0.03 1.00 16.00-18.00 0.5 - - - - 198 Max 440 Min 250 Min 18 Min
THICKNESS (mm) W ≤ 20mm W 21mm to 50mm W 51mm to 200mm W 200mm to 610mm
Th ≤ 0.25 S.E. + D.E. + R.E S.E. + D.E. + R.E S.E. S.E. + M.E
0.26 to 0.60 S.E. + D.E. + R.E S.E. + D.E. + R.E S.E. S.E. + M.E
0.61 to 0.80 S.E. + D.E. + R.E S.E. + D.E. + R.E S.E. S.E. + M.E